EXPLORING BASIC PLUMBING WHEN YOU INSTALL A BATHTUB

Exploring Basic Plumbing When You Install a Bathtub

Exploring Basic Plumbing When You Install a Bathtub

Blog Article

Schedule A Service Call

How do you feel when it comes to A Step-by-Step Guide to Installing a Bathtub?


Tools You Need to Install a New Bathtub
Installing a bathtub isn't specifically rocket science, yet it does require solid plumbing, woodworking, and also often, tiling abilities. Replacing an old tub with a new one is additionally a moderately difficult task. If the old tub is easily obtainable, the task can move immediately; if you need to open a wall surface to eliminate the old tub and place the new bathtub, the job is much harder. In either situation, the project is within a house handyman's abilities, although you will certainly need an assistant to vacate the old bathtub and embeded in the brand-new one. Ensure you have actually certified yourself for the task and fit trying it. Rather than working with a specialist to take control of a halfway-completed project, it is far better to think about utilizing one prior to you begin. Chances are you may require a professional plumber to make tube links.
This article will aid you install a new tub in your shower room if you have currently purchased a new bathtub and do not need to transform the setup of your previous water system pipes.
Your tools and also product checklist ought to consist of the following:
  • New Bathtub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipe Caps


  • Removing Old Touches


    If you need to change old taps with brand-new ones as a part of your setup, then the first thing you ought to do is detach the water system. After doing so, turn on the taps to drain any water remaining in the system. The process of eliminating the existing faucets can be fairly bothersome because of the limited accessibility that is commonly the situation.
    Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a fabric ready for the remaining water that will certainly originate from the pipes. When the supply pipes have been gotten rid of, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming throughout this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
    Prior to proceeding to fit the new taps, compare the pipe links on the old faucets to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new faucets to fit.

    Fitting New Taps


    If the tails of the brand-new faucets are plastic, then you will certainly need a plastic connector to prevent damage to the string. One end of the connector fits on the plastic tail of the faucet and also the various other end provides a link to the current supply pipelines.
    If you need to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
    Next off, place the faucet in the installing opening in the bath/basin guaranteeing that the washing machines are in area between the faucet and the sink. Safeguard the tap in position with the producer provided backnut. Once the faucet is securely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with typical tap adapters. The previous kind must be linked to the faucet ends initially, tightening only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.

    Setting up the Tub


    Using the two wood boards under its feet, position the tub in the needed placement. The wood boards are useful in equally spreading out the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four little points.
    The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by checking the spirit level as well as adjusting the feet on the bathtub until the level reads level.
    To mount faucets, fit all-time low of the outermost versatile tap port to the appropriate supply pipe by making a compression join; after that do the exact same for the various other faucet.
    Switch on the water and also inspect all joints and brand-new pipework for leaks and tighten them if necessary. Fill the tub as well as likewise examine the overflow outlet and the normal outlet for leaks.
    Ultimately, repair the bath paneling as defined in the producer's instruction manual. Tiling and also sealing around the bath tub should wait up until the bath tub has actually been used at the very least when as this will certainly resolve it into its last setting.

    Planning for the Setup


    First of all, the supporting framework supplied with the bathroom must be fitted (if called for) according to the maker's directions. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is very important to ensure that if the tap features a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets device to avoid pressure on the bath tub.
    Fit the flexible tap adapters to the bottom of both taps making use of 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you use every one of the provided washers.
    Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to currently prepare to be fitted in its last position.

    Tiling Around the Bath tub


    In the location where the bathroom fulfills the tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to fracture a rigid seal, creating the water to pass through the wall between the bath and the tiling, causing problems with moisture and possible leakages to the ceiling listed below.
    You can choose from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, and also can sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with twists of drenched paper or soft rope. Remember to always fill the tub with water prior to securing, to permit the motion experienced when the bathtub remains in use. The sealant can fracture relatively early if you do not think about this movement prior to sealing.
    Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also quickly readily available on the market. It is advisable to fit the tiles utilizing waterproof or waterproof sticky and also cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub

    I am just very occupied with Tools You Need to Install a New Bathtub and I hope you liked the new piece. Don't hesitate to take a moment to share this blog post if you enjoyed reading it. I treasure reading our article about Installing A Bathtub.


    We're on standby!

    Report this page